Port Devices


Posted On
Posted By admin

Efforts are underway to better integrate information from third parties. Improper probing will give deceiving results. Only one output should be shorted at a time, do not exceed maximum junction temperature specification. Multiple vias should be used to connect the decoupling capacitors to the power planes. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. It takes a single-ended 3 V logic signal and converts it to a differential current output. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied.

Uploader: Narr
Date Added: 3 May 2016
File Size: 51.83 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 63100
Price: Free* [*Free Regsitration Required]

Carefully review dimensions to match differential impedance and provide isolation for the differential lines. CL includes probe and jig capacitance. Math HW 9. Output Signals MS External lower value pull up and pull down resistors for a stronger bias may be used to boost fail-safe in the presence of higher noise levels.

DS90LV031 3V LVDS Quad CMOS Differential Line Driver

The termination lvxs converts the current sourced by the driver into a voltage that is detected by the receiver. Channel 3 Inverting Output Current Driver. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.


On the printed circuit board, this distance should remain constant to differentual discontinuities in differential impedance.

This configuration provides a clean signaling environment for the quick edge rates of the drivers. The output current is typically 3. If a fault condition occurs that shorts the receiver inputs together, thus resulting in a 0V differential input voltage, the receiver output will remain in a HIGH state.

At the receiver, this current develops a positive differential voltage across RT with respect to the inverting input and results in a Logic 1 at the receiver output. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits.

3 V, LVDS, Quad, CMOS Differential Line Driver ADN

AC or unterminated configurations are not allowed. TI is not responsible or liable for such altered documentation. Current out of device pins is defined as negative. Current out of device pins is defined as negative. Plus, noise induced on lvdds differential lines is much more likely to appear as common-mode which is rejected by the receiver. Driver Channel 2 Logic Input.

TI has discontinued the production of the device. Driver Output Levels http: The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates.

All typicals are given for: Shorted input fail-safe is not supported across the common-mode range of the device GND to lone.

Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices.


Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer’s risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. Finish options are separated by a vertical ruled line.

Enable Inputs Truth Table Current-mode drivers offer considerable advantages over voltagemode drivers such as RS drivers. The TRI-STATE function allows the driver outputs to be disabled, thus obtaining an even lower power difterential when the transmission of data is not required.

The current mode driver provides substantial benefits over voltage mode drivers, such as an RS driver. This also powers down the device ljne reduces the current consumption from typically 23 mA to typically 2. This component has a RoHS exemption for either 1 lead-based flip-chip solder bumps used between the die and package, or 2 lead-based die adhesive used between the die and leadframe.

Lcds published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Channel 1 Noninverting Output Current Driver. Pin Configuration Table 4.

An additional application condition may exist also.